產品特性

本產品采用無機天然顏料與有機高分子聚合物合成固化后具有粘結力強、致密不開裂、防霉抗?jié)B等特點，并且可以在潮濕場合使用。耐擦洗、不褪色，易于清潔，健康環保。

Product Features

This product adopts inorganic natural pigments and organic high polymer after synthesis and curing, and can be used in wet occasions with the characteristics of strong adhesion, compact and non-cracking, mildew proof and impermeable, resistant to scrubbing, fadeless, easy to clean, healthy and environmental protection.

主要成分

低堿硅酸鹽水泥、天然無機顏料、石英粉、微硅粉和可再分散膠粉、抗裂纖維、保水劑等添加劑。

Main Ingredients

Low alkali Portland cement, natural inorganic pigment, quartz powder, micro silicon powder and redispersible gelatin powder, anti-crack fiber, water retention agent and other additives.

施工說明

本產品為二合一的單組份干粉材料，適用于瓷磚粘貼也可填縫，開袋加水30%攪拌即可施工，首先將瓷磚縫隙中的灰渣清理干凈，再用濕海綿將縫隙表面濕潤，以利于提高填縫劑的固化強度，同時有利于避免填縫劑對瓷磚毛細孔的滲透。用工具將填縫劑膠漿填滿壓實，填縫劑初步固化后(15-30分鐘)，用微濕海綿將瓷磚表面多余的填縫劑清理干凈。如果應用于外墻面粘貼小型瓷磚，可采用滿粘法施工。理論上滿粘時每平米(厚度1mm)用量在1.5kg左右，填縫時1公斤可以滿足約3平方米的瓷磚(縫隙寬度5mm-8mm)。

Construction Descriptions

This product is a two-in-one single-component powder material, suitable for ceramic tile paste and caulking, open the bag, add 30% water and construction can be done after stirring. First of all, clean up the ash of ceramic tile aperture, and then moisten the crack surface with wet sponge so as to enhance caulking agent curing strength and to avoid caulking agent to ceramic tile capillary permeability. Fill and compact the glue paste of the caulking agent with tools. After the initial curing of the caulking agent (15-30 minutes), use a slightly wet sponge to clean up the excess caulking agent on the tile surface. If applied to the external wall paste small ceramic tiles, it can be constructed in the full adhesion method. Theoretically, the consumption of each square meter (thickness of 1mm) is about 1.5kg for full adhesion, and 1kg can satisfy about 3 square meters of ceramic tiles (gap width 5mm-8mm) for filling seam.

注意事項

1. 本產品加水即用，禁止摻加其他材料改變填縫劑的配比和性能。 2.施工溫度應在5℃~40℃，切忌將已干結的膠漿加水?dāng)嚢柙儆谩? 3.施工前應以小面積局部試驗后再大面積施工。如表面粗糙的瓷磚應選用相近的顏色或小面積試用，否則會出現污染磚面的情況。 4.不能在雨淋的情況下施工，應在施工8~9小時灑水養護。

Cautions

1. The product can be used after adding water and it is forbidden to mix other materials to change the ratio and performance of the filler.

2. The construction temperature should be between 5℃ and 40℃ and it is forbidden to mix the dried glue pulp with water before use.

3. Before construction, local tests should be conducted in a small area before construction in a large area. If the ceramic tile with rough surface, choose close color or make a trial in the small area, otherwise it may appear contaminative brick face circumstance.

4. Construction should not be carried out in the case of rain, and water maintenance should be sprayed 8-9 hours after the construction.