產品說明

水不漏是由特種水泥及添加劑調制而成的防水堵漏產品;具有強度高,快速硬化等特點,快速修補、抗?jié)B防潮防水,適用于滲漏基體上做防水堵漏，可帶水施工。

產品特點

1、防潮、抗?jié)B、快速堵漏。

2、迎水面、背水面均可施工。

3、抗?jié)B壓強,粘結高。

4、與基體結合緊密成一個整體,不易老化,耐水性好。

Product Description

Water Leakage Stoppage is a waterproof plugging product made of special cement and additives modulation; with the characteristics of high strength and fast hardening, it is impervious, moisture proof and waterproof and can be repaired quickly and constructed with water, suitable for waterproof and plugging on the leaking substrate.

Product features

1. Moisture proof, impermeable, fast plugging.

2. Construction can be carried out on the water surface and the water surface.

3. Impermeable pressure, high bonding.

4. It is closely combined with the base into a whole, not easy to aging, good water resistance.

適用范圍

1、各種地下建筑物或構筑物、電纜溝道、水池、廁衛間、人防洞庫、地鐵、隧道等工程的防潮、抗?jié)B。

2、穿墻管、套管、管口周邊、陰陽角的修補和加固。

3、廚衛間、地下室、屋面等裂縫或缺陷修補加固。

4、掛鉤件、設備欄桿的固件。

Scope of Application

1. Moisture proof and anti-permeability projects of all kinds of underground buildings or structures, cable channels, pools, toilets and bathrooms, civil air defense caverns, subways, tunnels, etc.

2. Repair and reinforcement of wall pipes, casing, around pipe orifice and internal and external angles.

3. Repair and reinforcement of cracks or defects in kitchens, bathrooms, basements, roofs and other places.

4. Fasteners for hooks and equipment railings.

施工方法

基層處理:

施工前應確?；鶎咏Y(jié)實、無粉塵、無雜物、無油污汲其它松散物。

Construction Method

Base Treatment:

Make sure that the base is firm, free from dust, sundries and grease before construction.

漿料攪拌:

將適量清水倒入干凈容器內,加入粉料,每公斤粉料需要0.3~0.5L清水(加水量可根據施工人員手感以及環境溫度和濕度而調整) , 快速攪拌直至形成無結團

Slurry Mixing:

Pour proper amount of water into the clean container and add powder. 0.3-0.5L of water is needed for each kilogram of powder (the amount of water added can be adjusted according to the construction worker’s feel and the ambient temperature and humidity). Stir quickly until no agglomerate.

堵漏修補:

一般防水工程的滲漏水形式主要表現為三種,即點、縫和面的滲漏。根據工程滲漏水具體情況,可用速凝型防水堵漏寶采用不同止水堵漏工藝進行整治。

Leakage Stoppage and Repair:

The seepage form of general waterproof project basically shows for 3 kinds, namely point, joint and surface leakage. According to the specific project leakage, the quick-setting type of waterproof plugging treasure can be used for the treatment of different water plugging technology.

1 )漏水孔洞的防水堵漏;

漏水孔周圍部位的防水處理將粉料加水拌合后涂抹在漏水孔周圍, -般采用抹子或刮板涂抹2~3遍。每- -遍需待涂層硬化后(手壓不留指紋),將其噴濕(但不能有積水),再進行下一遍施工。剔圓形槽堵漏以漏水點為圓心剔槽(槽的直徑x深度為10mmx 20mm、20mm×30mm, -般毛細孔滲水剔成直徑10mm圓孔), 用水將槽沖洗干凈。將粉料加水拌合后捏成與槽直徑相近的圓錐體,放置片刻待用手捏有硬感時,將其塞進槽內,并用木棒擠壓,輕砸使其向內部及四周壓緊、擠實,即可瞬時止水。

1) Waterproof and Plug Leakage of Leaking Holes

The waterproof treatment of the parts around the leak hole will add water powder and apply it around the leak hole, generally using a trowel or scraper daub 2-3 times. After the coating has hardened (hand pressure does not leave fingerprints), spray it with water (but no waterlogging), then proceed the construction to the next time. Pick the circular groove plugging with the water leakage point as the center of the pick groove (the diameter x depth of the groove is 10mm × 20mm, 20mm×30mm, for the capillary porous water cut into a diameter of 10mm round hole), rinse the groove with water. Mix the powder with water and shape it into a cone with a diameter similar to that of the tank. When it is hard to be pinched by hand for a while, put it into the tank, squeeze it with a wooden stick, and gently hit it so that the inside and the surrounding are pressed and compacted. Then the water can be stopped instantly.

2 )漏水裂縫的防水堵漏

漏水裂縫周圍部位的防水處理 將粉料加水拌合后涂抹在漏水縫隙周圍, -般采用抹子或刮板涂抹2~3遍。每一遍需待涂層硬化后(壓不留指紋),將其噴濕(但不能有積水)，再進行下一遍施工。剔八字型槽堵漏沿裂縫剔深為10mm~30mm,寬15mm~ 50mm的八字型槽。在槽底沿裂縫放一小繩,繩長約200~300mm。將粉料加水拌合后捏成條形,放置片刻待用手捏有硬感時,填壓于放繩的槽內,并迅速將邊緣壓實,隨即將繩子抽出,再壓實-次,使漏水順繩孔流出。對較長的裂縫可分段逐次填塞，每段長約100mm~ 150mm每段間隙留20mm寬空隙。在20mm空隙處,用裹上拌合料的釘子待拌合料將要凝固時插入空隙中,并迅速用拌合料將釘子的四周空隙壓實,同時轉動釘子并立即拔出,使水順釘孔流出。待堵漏料凝固后,再按漏水孔洞的防水堵漏辦法處理釘孔。

2) Leakage of Water Cracks Waterproof Plug

The waterproof treatment of the parts around the leak crack will add water powder and apply it around the leak crack, generally using a float or scraper daub 2-3 times. After hardening of the coating (pressure without fingerprints), spray it wet (but not water), and then proceed with the next construction. The K-type slot is 10mm-30mm deep and 15mm-50mm wide along the crack. Put a small rope at the bottom of the trough along the crack, and the rope length is about 200-300mm. Mix the powder with water and shape it into a strip. When it is hard to be pinched by hand for a moment, fill and press it into the slot where the rope is placed. Then, the edge of the rope is quickly compacted. For the longer cracks can be piecewise and successive filling, the length of each section is about 100mm-150mm and the gap of each section is 20mm wide. At the 20mm gap, insert the nails coated with mixing material into the gap when the mixing material is about to solidify, and quickly use the mixing material to compress the gaps around the nails, at the same time turn the nails and pull them out immediately, so that the water flows out along the hole. After the plugging material solidifies, the nail hole shall be treated according to the waterproof plugging method of the leaking hole.

注意事項

1、凝結時間會因用水量、施I溫度不同而有波動。

2、材料需要一次性拌和 ,可二次加水拌和,可使用時間約5分鐘(視溫度和濕度而定) ,初凝后不可加水再用。

3、凝結時可能會大量放熱,應小心避免燙傷。

4、本品僅適用于不帶壓的結構修補。

產品保存

存放于陰涼干燥處,嚴禁雨淋受潮,貯存溫度5- 35°C ,未啟封產品可保存12個月。

Cautions

1. The setting time fluctuates due to different water consumption and construction temperature.

2. The material needs to be mixed once, and can be mixed with water twice. It can be used for about 5 minutes (depending on the temperature and humidity).

3. A large amount of heat may be generated during condensation, so take care to avoid scalding.

4. This product is only applicable to the repair of the structure without pressure.

Product Storage

Store in a cool and dry place, no rain or dampness. Store at 5°C-35°C. The unopened products can be stored for 12 months.